Quantity

Size/Grade

Tool or Item

Comments

Turning Tools:

1

3/8"

Bedan or Beading and Parting Tool

Essential tool for making tenons.

1

1/16" to 1/8"

Parting Tool (sometimes called a Cutoff Tool)

A diamond shape is better tan rectangular.

1

3/4" to 1-1/4"

Roughing Out Gouge

The wider the better!

1

1" or wider

Skew Chisel

You have three choices, standard, rolled edge and oval. Oval is the easiest to use mad probably the best choice for beginners.

1

1/2"

Spindle Gouge

With a fingernail grind.

1

4" to 6"

Calipers

Good for checking diameters, but don't rush and buy.

1

4" to 6"

Dividers

Good for stepping off distances, but a ruler and a pencil will do the job fine.

Joinery Tools:

1

10 to 18 point

Backsaw

Crosscut or rip filing is o.k. Avoid very thin backsaws, especially Japanese for they do not work well for half-blind dovetails.

1

#5

Bench Plane (Must Have)

Do not rush out and buy new planes. It is Ernie's feeling that classic planes (found at any flea market) work better and are a better value than new planes. New planes generally require more tuning than a classic. We have classics available in our store. They are guaranteed by Ernie to work to perfection and are generally less expensive than new planes.

1

#4 or #3

Bench Plane (Nice to Have)

If you are going to buy new Lie-Nielsen, Clifton or Veritas are the only ones worth your consideration. Do not buy Indian planes.

1

Bevel

We often have antique bevels in our store

1

Cabinet Scraper

Used primarily for half-blind dovetails.

1

Carvers Mallet

Round wooden type is best, the rubber headed types are too "bouncy. Avoid hammer type mallets. Japanese metal chisel driving hammers are good and what Ernie uses.

1

12"

Combination Square

 The Starrett Combination square is a good investment.

1

4" to 6"

Dividers

Size refers to length of legs and a small pair is better!

1

Ear Protection

Ear muffs are easiest to use but plugs are fine.  (Absolutely must have)

1

12, 14 or 16 oz

Hammer

Standard claw or Japanese are fine.

1

Marking / Mortising Gauge

Traditionally marking and mortising gauges were separate tools but now days they are combined into one tool for economy. If you have separate marking and mortising, that is fine.

1

Notepad

1

chunk

Paraffin Wax

Canning wax is perfect and can be found at most grocery stores. An old candle will do.

1

Pencil

1

Pliers (Vice grip or tongue and groove)

Good for pulling nails loosening stubborn screws and lids, etc.

1

Tape or Folding

Ruler

6" or 12" steel rule is also nice to have and a folding rule is more accurate than a tape.

1

Safety Glasses

You must have a minimum of safety glasses, Most prescription glasses are safety lenses, but need side shields to be true safety. If in doubt bring face shield to go over glasses.

2

120 grit

Sandpaper

We favor Klingspore PS 33 in a B weight which is a stearated, open coat, aluminum oxide paper.

2

180 grit

Sandpaper

We favor Klingspore PS 33 in a B weight which is a stearated, open coat, aluminum oxide paper.

2

220 grit

Sandpaper

We favor Klingspore PS 33 in a B weight which is a stearated, open coat, aluminum oxide paper.

2

8" to 10"

Screw Clamps

Size refers to length of jaw

1

Straight

Screw driver

1

Phillips

Screw driver

1

1/4" to 3/4"

Set of Bevel Edge Chisels (Also known as Carpenter's chisels)

Buy an 8 (or even 10) piece set, rather than a 5, if you can afford it. It is most useful to have a 1/8" chisel for dovetails. Be sure to buy "bench" chisels and not the shorter "butt" chisel which is commonly all that is available at hardware stores. Japanese chisels (Oire-Nomi) are excellent but expensive. The Japanese drive their chisels with a Japanese hammer and this is Ernie's practice.

Optional

5/8”

Japanese Butterfly Chisel

(Bachi Nomi)

This is a great chisel for half-blind dovetails (in place of an 1/8”) even if the rest of your chisels are English. This is item 15.307.15 in the Japan Woodworker Catalogue. (www.japanwoodworker.com)

1

Stanley #92 or #93

Shoulder Plane

Clifton's are very good as are Lie-Nielsen and Veritas.

1

Straight Edge

12"Steel Rule is fine which is the blade to your combination square

1

stick

White Chalk

Nice To Have Tools, But Not Necessary:

1

5/8”

Japanese Butterfly Chisel

(Bachi Nomi)

This is a great chisel for half-blind dovetails (in place of an 1/8”) even if the rest of your chisels are English. This is item 15.307.15 in the Japan Woodworker Catalogue. (www.japanwoodworker.com)

2 to 4

That will span 32"

Bar clamps

We have lots, but if you are driving and feel like throwing a couple in they will come in handy.

1

Crosscut

Hand Saws

Ernie recommends pre WWII so check with our store for antiques.

1

rip

Hand Saws

1

1/4"

London Pattern Mortise Chisel

We have plenty of loaners at the workshop

1

Your own sharpening system

We have a Tormek system as well as plenty of whetstones but you may want help learning to use your own.